Shopruger.comCorporateCastingsLE/Military



FAQs

Simply select a category and then click the "Answer" button next to the question for information on that topic.
If you cannot find the answer to your question below, please Click Here for contact information.

Do you have a toll-free phone number?
No. We provide direct dial numbers to each facility and feel that our customers appreciate having 'live' operators answer the phone. For Company phone numbers, click here.

Do you give factory tours?
For safety and proprietary reasons, we do not offer tours of our facilities.

Can I buy a firearm directly from the factory?
No. Ruger sells only to independent federally licensed wholesale distributors, who in turn sell to federally licensed retailers.

How can I get an instruction manual for my gun?
Ruger instruction manuals for both currently produced and out-of-production models can be downloaded directly from this website by clicking here. Note that prices listed in manuals are subject to change at any time. For current pricing, please contact the Service Department. Click here for contact information.

How do I ship my gun to the Service Department for service/repair?
Click here for shipping instructions. Note that custom gunsmithing is not available from Ruger. Custom engraving is available through the Ruger Studio. Click here for Ruger Studio information.

What is the life expectancy of my Ruger firearm?
Ruger firearms have a very good reputation for service life. With proper handling and care, you should receive many years of service from our products. However, any firearm may be irreparably damaged in short order by abuse or neglect, so it is impossible to state the life expectancy of any Ruger firearm.

Why does Ruger ship a fired cartridge case with every pistol and revolver?
Certain states require that all newly manufactured pistols and revolvers be accompanied by a cartridge case that has been test fired from that gun at the factory. The case must be placed in a sealed container bearing certain information concerning this test cartridge. At the time of retail sale in those jurisdictions with the requirement, firearms dealers must forward the test cartridge to a designated destination such as their State Police Laboratory. As independent Ruger Distributors have nationwide markets without territorial restrictions, we have decided to include a fired cartridge case with all new Ruger pistols and revolvers to minimize the possibility of inadvertent non-compliance with these laws. Retail customers located in states that do not require a fired cartridge case may be assured that the fired cartridge case they receive with the firearm at the time of retail purchase is proof that your new Ruger firearm has undergone our normal test firing procedures during manufacture.

What is my Ruger firearm worth?
Unfortunately, we cannot put a value on a firearm after it has left the factory. There are books on firearm values available at either your local bookstore or library that you may find helpful. You may also contact the Ruger Collector's Association for further information. Please note that this organization is not associated with or a part of Sturm, Ruger, and we are not responsible for any information provided to you. They may be reached at Ruger Collector's Association, Attention: Jay Hansen, P.O. Box 240, Greens Farms, CT 06838 or by calling Jay Hansen at 203-259-9498 extension 124.

Can you tell me the date my firearm was manufactured if I give you the serial number?
General serial number information can be found in the Instruction Manuals & Product History pages. For specific information regarding your serial number, please call our Service Departments:
• Rifles, Shotguns, Revolvers: 603-865-2442
• Pistols: 928-541-8892.
For serial numbers manufactured prior to our electronic records, or for an official letter confirming the details on your firearm please download and mail in the Request for Letter of Authenticity form.

Does Ruger provide reloading information for my gun?
No. We recommend that only factory ammunition manufactured to U.S. Industry Standards be used in any Ruger firearm.

Why do you recommend not shooting reloaded ammunition?
Death, serious injury, and damage can result from improper ammunition, bore obstructions, powder overloads, or incorrect cartridge components. Even the strongest gun can be blown up by excess pressure. Only use correct ammunition loaded to U.S. Industry Standards. Always wear shooting glasses and hearing protectors. Improper ammunition destroys guns. We specifically disclaim responsibility for any damage or injury whatsoever occurring in connection with, or as a result of, the use in any Ruger firearms of faulty, or non-standard, or 'remanufactured' or hand-loaded (reloaded) ammunition, or of cartridges other than those for which the firearm was originally chambered.

I purchased a firearm for a specific use and now I think I bought the wrong model. Will you exchange it for a different model?
No. Once you purchase a firearm, it becomes your property, so please be sure you are buying what you need and want.

Where can I purchase Ruger® firearms?
Please contact your local, federally licensed firearms retailer. For your convenience, we offer a retailer locator on our website at www.ruger.com/retailer/find.html.

What is an RMA number?
An RMA number stands for "Return Material Authorization" number. We ask that you call the Service Department to receive an RMA number before shipping your firearm in for service. This number allows us to quickly and properly process your firearm.

Why No Warranty Card Has Been Packed With Your New Ruger Firearm?
The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty. It does provide that if a written warranty is given, it must be designated as "limited" or as "full" and sets minimum standards for a "full" warranty. Sturm, Ruger & Company, Inc. has elected not to provide any written warranty, either "limited" or "full", rather than to attempt to comply with the provisions of the Magnuson-Moss Act and the regulations issued thereunder. There are certain implied warranties under state law with respect to sales of consumer goods. As the extent and interpretation of these implied warranties varies from state to state, you should refer to your state statutes. Sturm, Ruger & Company wishes to assure its customers of its continued interest in providing service to owners of Ruger firearms.

Can I buy a standard model revolver and send it to Ruger and have it made into a distributor special?
Unfortunately that is not a service we offer.

I purchased a Ruger firearm that was a limited-run distributor special. Will you service this firearm?
Yes, we can service the mechanical parts of these guns. Some distributor specials require "one-time only" fabricated components (i.e. engraved plates, special wood stocks, etc.) which may or may not be available. For more information on specific serviceability questions, please contact the Service Department. Click here for contact information.

I sent my gun in for service. Can I find out the status?
Yes, by calling the correct Service Department. Please be sure to have your serial number or repair order number available when you call. If you recently sent your gun in, please wait to call until you receive a repair order number from us in the mail. If a retailer sends the gun in for service, the retailer will receive the repair order information. However, customers may call us directly as long as they have the serial number available. Click here for contact information.

Why are some parts restricted for sale to the public?
There are state regulations on certain parts and some parts require fitting to a specific firearm for proper functioning and safety.

Why do some replacement parts require factory fitting?
Some parts require special fitting that we feel can best be fitted by our trained technicians at the factory. Also, every gun is test fired for proper functioning before it is returned to the customer.

If any factory parts in my Ruger gun have been altered or modified, will the Service Department perform repairs on the gun?
Ruger firearms are designed to function properly in their original condition. Sturm, Ruger will not be responsible for any alteration of any part of the firearm, or for the addition or substitution of parts and accessories not manufactured by Sturm, Ruger & Co., Inc. If firearms sent in for service are found to be altered, they may be brought back to factory specifications at the discretion of Sturm, Ruger and at the expense of the customer. So please remove any custom parts and accessories prior to shipment to Ruger for service.

Does Ruger service discontinued models?
We still offer service for many discontinued models. However, we do not offer service on some older discontinued models because the parts are no longer available. Contact our service departments for more complete information.

Can I have my 'old model' single-action revolver serviced or order parts for it without having the conversion kit installed?
In order to encourage our customers to take advantage of the free safety update, no service work will be done on the 'old model' single-action revolvers unless the conversion kit is installed. We also will not sell parts for the revolver unless it has been converted.

May I speak directly to a technician at the factory?
No. Our firearms technicians are occupied servicing firearms and are not available to take phone calls. Any questions should be directed to the Service Department phone operators.

Does Ruger offer custom gunsmithing services?
No. Although Ruger offers factory service on firearms that we manufacture, we do not offer any custom gunsmithing services. We do offer custom engraving through the Ruger Studio.

Can Ruger refinish older firearms?
Ruger offers refinishing for most firearms that we manufacture. Click here for more information.

Can I place a parts order online?
We currently offer 10/22®, Mark I™, MarkII™, MarkIII™, P-Series, LCP®, LC9™, SR1911™, SR40®. SR40c™, SR9® and SR9c™ spare parts at shopruger.com. For more information about parts, visit our Parts Ordering Page.

Can I purchase scope rings online?
Yes. Please visit ShopRuger.com

Can I exchange the Ruger scope rings that I received with my new gun for a different sized set?
If the gun was recently purchased and was purchased brand new, we will exchange the new, unused rings that were provided with that firearm with a new set of different model rings more suited to the scope selection. Please note that altered or used scope rings will not be exchanged. Click here for contact information.
Note: Because of the complex US export laws and costs associated with the export of firearm parts, this option is not available to our foreign customers. Please contact the Ruger distributor in your country for information on obtaining scope rings.

Will Ruger repair fire damaged firearms?
We cannot service firearms that have been damaged by fire or corrosion. Please call the Service Department for more information.

Can I dry fire my Ruger shotgun?
Yes. All Ruger shotguns can be dry fired without damage, and dry firing can be useful to familiarize the owner with the firearm. However, be sure any firearm is completely unloaded before dry firing!

How can I get an instruction manual for my Ruger shotgun?
Ruger instruction manuals for both currently produced and out-of-production models can be downloaded directly from this website by clicking here. Note that prices listed in manuals are subject to change at any time.

Are different sights available for my shotgun?
Yes, different sights are available. If you'd like to purchase new sights, please visit ShopRuger.com.

What comes with my Ruger SR-556?
Your Ruger SR-556 comes with an owner's manual, three Magpul magazines with dust/impact covers (with the exception of the SR-556E which comes with 1 mag), rail covers, a lock and a sight adjustment tool.
Watch Video

How do I adjust the Troy Industries Folding Battlesights on the SR-556?
You can adjust the sights with your sight adjustment tool, provided with your SR-556, or a coin. Rotating clockwise results in rightward adjustments. Counterclockwise rotations move the sights leftward. Elevation adjustment can be accomplished by rotating right, threading the sight post inward and lowering it, thus raising impact.
If you turn left and thread the sight-post out, you will raise the sight-post and lower bullet impact.
Watch Video

At what setting should I run my SR-556 gas regulator?
Since there is no benefit to running your gun at a setting higher than what is necessary, always opt to run your SR-556 on the lowest possible reliable gas setting. One way to tell if you are on the correct setting is to observe ejection pattern. When firing, the brass should eject just to your right.
Watch Video

How do I access the transfer rod on my SR-556?
You don't need to. They are made to outlast the barrel. The transfer rod is coated with Nickel-Teflon®, and the return spring is made of stainless steel. Our testing has shown that even without cleaning or lubrication, the transfer rod and spring will outlast the barrel.
Watch Video

Does the SR-556 have carrier tilt?
From the two-stage piston to the adjustable regulator, many features have been introduced to limit the effects of carrier tilt.
Watch Video

How do I remove the flash suppressor on my rifle?
A Torx T60 bit can be used to remove the suppressors, all of which are installed with standard, right hand threads. All newly made (2009+) rifles (except the SR-556C and CLA models; the flash hiders for these models are integral to the barrel and not removable) are threaded ½-28 (22 and 223 caliber) or 5/8-24 (6.8 and 30 cal.).

I'm having trouble inserting my Mini-14 magazine. How do I properly insert and remove these magazines?
The Mini-14 magazine is not inserted or removed with a straight "up" and "down" procedure. Rather, the magazine must be inserted at an angle and then locked into place by rocking it in, front to rear, and removed by rocking it out, rear to front. Also, for higher capacity magazines (10-, 20-, or 30-round), relatively higher amounts of force may be required.

Click here to see an illustrated PDF with step-by-step instructions for Mini-14 magazine insertion and removal.

Can I shoot 5.56 NATO ammunition in my Mini-14 or Ranch Rifle?
With the exception of the Mini-14 Target Rifle, which accepts only .223 Rem. ammunition, .223 Rem. and 5.56 NATO can be used in all Mini-14 rifles and Ranch Rifles.
Please note that "Military Surplus" 5.56mm NATO can vary greatly in its quality and consistency.

I have heard that Ruger has changed the 10/22 carbine trigger group components from aluminum to polymer. Is this true and, if so, why was this change made?
Yes, it is true that we have updated the 10/22 trigger group components and that they are now made of glass-filled polymer instead of the die cast aluminum parts. Ruger engineers are always looking for ways to improve our products, including evaluating new and evolving technologies and materials. The benefits of polymers are many, including improved impact resistance, an unmatched ability to withstand the elements, and of course weight savings. Accordingly, polymers are routinely used in firearms that are subjected to heavy use in harsh conditions, law enforcement and military applications in particular. The new trigger group features injection molded components of high tech polymer for an improved product with closer manufacturing tolerances. The firearm is as reliable and, because the color is incorporated into the polymer of the injection molded components, the finish will never wear off due to normal use or unexpected abrasion. Also, the heat stabilized, glass-filled polymer will withstand impacts that would bend or even break the die cast aluminum parts previously used in Ruger 10/22's.

Click here to check out a video by Guns & Ammo TV that demonstrates the strength and durability of the new polymer trigger guard.

Can I dry fire my Ruger rifle?
Yes. All Ruger rifles can be dry fired without damage, and dry firing can be useful to familiarize the owner with the firearm. However, be sure any firearm is completely unloaded before dry firing!

How can I get an instruction manual for my Ruger rifle?
Ruger instruction manuals for both currently produced and out-of-production models can be downloaded directly from this website by clicking here. Note that prices listed in manuals are subject to change at any time.

Can I have my rifle fitted with a different length barrel than the one with which it was initially shipped?
No, we do not offer fitting of different barrel lengths or calibers on rifles.

Can I have a factory synthetic stock fitted to my rifle if it was initially shipped with a wood stock?
Yes, but only for certain models and at the customer's expense. Please contact the New Hampshire Service Department directly at 603-865-2442. Please be sure to have your firearm's serial number available when you call.

What type of ammunition should I use with my Ruger rifle?
Only factory ammunition manufactured to U.S. Industry Standards should be used in a Ruger firearm. We specifically disclaim responsibility for any damage or injury whatsoever occurring in connection with, or as the result of, the use in Ruger rifles of faulty, or nonstandard, or 'remanufactured' or handloaded (reloaded) ammunition, or of cartridges other than those for which the firearm was originally chambered. Improper ammunition destroys guns!

Are different sights available for my rifle?
Yes, different sights are available. If you'd like to purchase new sights, please visit ShopRuger.com.

Can I exchange the Ruger scope rings that I received with my new rifle for a different sized set?
If the gun was recently purchased and was purchased brand new, we will exchange the new, unused rings that were provided with that firearm with a new set of different model rings more suited to the scope selection. Please note that altered or used scope rings will not be exchanged. Click here for contact information.
Note: Because of the complex US export laws and costs associated with the export of firearm parts, this option is not available to our foreign customers. Please contact the Ruger distributor in your country for information on obtaining scope rings.

How do I remove the flash suppressor on my rifle?
A Torx T60 bit can be used to remove the suppressors, all of which are installed with standard, right hand threads. All newly made (2009+) rifles (except the SR-556C and CLA models; the flash hiders for these models are integral to the barrel and not removable) are threaded ½-28 (22 and 223 caliber) or 5/8-24 (6.8 and 30 cal.).

Are the Ruger PC4 and PC9 Carbine models discontinued?
Ruger has discontinued production of both the PC4 and PC9 Carbines due to low demand. We will, however, continue to service these models. If you need service or repair, please contact the Service Department. Click here for contact information.

Will Ruger reblue or refinish my PC4 or PC9 Carbine?
So long as your Ruger Carbine rifle has not been damaged by fire, immersion or corrosion, it can be refinished at our Prescott plant. The complete rifle must be sent to our Prescott Customer Service Department. Click here for shipping contact information.

What is the trigger pull on Ruger PC4 and PC9 Carbines when they are manufactured?
Factory specifications are 6 to 10 lbs.

How can I get an instruction manual for my PC4 or PC9 Carbine?
Ruger instruction manuals for both currently produced and out-of-production models can be downloaded directly from this website by clicking here. Note that prices listed in manuals are subject to change at any time.

Sometimes when I shake my Ruger LCR revolver, I hear a slight rattle; is that normal?
Like all newly manufactured Ruger revolvers, your LCR has a transfer bar safety system as part of the fire control mechanism. As a result, a hammer blow can be transmitted to the firing pin only when the trigger is pulled all the way to the rear. This is a positive internal safety feature. By design, the transfer bar is allowed some movement within the fire control mechanism so that trigger pull is not affected. Due to this necessary "play" in the transfer bar, a shooter will sometimes hear the transfer bar "rattle" when the revolver is shaken. This rattle caused by the play in the transfer bar is completely normal in the LCR.

Will the LCR be available for sale in California and/or Massachusetts?
Yes, though we anticipate a short delay while the revolver is submitted to an independent test lab for state-mandated testing. After that, it will depend upon how long the state agencies take to place the LCR on the approved rosters.

Can I dry fire my Ruger revolver?
Yes. All Ruger revolvers can be dry fired without damage, and dry firing can be useful to familiarize the owner with the firearm. However, be sure any firearm is completely unloaded before dry firing!

How can I get an instruction manual for my Ruger revolver?
Ruger instruction manuals for both currently produced and out-of-production models can be downloaded directly from this website by clicking here. Note that prices listed in manuals are subject to change at any time.

What type of ammunition should I use with my Ruger revolver?
Only factory ammunition manufactured to U.S. Industry Standards should be used in a Ruger firearm. We specifically disclaim responsibility for any damage or injury whatsoever occurring in connection with, or as the result of, the use in Ruger revolvers of faulty, or nonstandard, or 'remanufactured' or handloaded (reloaded) ammunition, or of cartridges other than those for which the firearm was originally chambered. Improper ammunition destroys guns!

Are different sights available for my revolver?
Yes, different sights are available. If you'd like to purchase new sights, please visit ShopRuger.com.

Does Ruger offer holsters for revolvers?
Yes. Ruger offers holsters for many models. Further information may be obtained at ShopRuger.com.

Can I exchange the Ruger scope rings that I received with my new revolver for a different sized set?
If the gun was recently purchased and was purchased brand new, we will exchange the new, unused rings that were provided with that firearm with a new set of different model rings more suited to the scope selection. Please note that altered or used scope rings will not be exchanged. Click here for contact information.
Note: Because of the complex US export laws and costs associated with the export of firearm parts, this option is not available to our foreign customers. Please contact the Ruger distributor in your country for information on obtaining scope rings.

If I purchase a SR40 with a 10 round magazine then purchase a 15 round magazine will it fit flush or fit at all?
An SR40 pistol will take either the 15 round magazine, or the "State Compliant" full size 10 round magazine.

Why do the new SR magazines have a matte finish instead of the gloss finish?
Recently we had our supplier add an "anti-friction coating" or AFC to the SR magazines. This coating makes loading the rounds in the magazine easier and the magazine is easier to insert and remove from the pistol. As we use up our stock of glossy magazines they will be replaced with ones with the AFC applied.

I want to buy an LCP, but can't find one. Is Ruger making them?
Yes, we are making the LCP pistols. The LCP has been very successful in the marketplace and the demand is very high, resulting in limited availability.

I have a LCP with serial number prefix 371 (or 372); is it affected by the recall?
No. Pistols with a "371" serial number prefix or higher are not affected.

Only pistols bearing prefix "370" (that is, serial number 370-xxxxx) may be affected.
Also, newly manufactured and retrofitted "370" prefix LCP pistols with the new hammer mechanism installed have been marked with a diamond in the flat portion of the slot just behind and below the hammer. Click here to see image of diamond mark and complete LCP recall information.

How can I tell if my Ruger SR9 pistol has been retrofitted?
If you own an SR9 pistol bearing a serial number below 30000 (that is, 330-29999 or less), you own an original SR9 pistol that was affected by the product safety recall issued in April, 2008. If you purchased a used SR9 that falls within this serial number range, it is easy to tell if it has already been retrofitted simply by looking at it. Although both the old and new trigger group have a two-stage trigger, the original design had an inner "shoe" that was not visible and, therefore, appeared to be a single trigger. The new trigger design incorporates a visible inner trigger of a blade design.

Click here for complete SR9 Recall information and to see images of the old and new trigger group designs.

If you own an SR9 pistol that has not been retrofitted, please contact us immediately to arrange return of the pistol.

What is the service life of the LCP?
There are many variables that can affect the service life of a firearm, such as the type of ammunition used and how it has been cleaned and maintained. As with all Ruger firearms, proper care is necessary to keep your LCP functioning properly and safely. If you have any concerns about the functioning of your pistol, please return it to our Arizona Service Department at 200 Ruger Road, Prescott, AZ 86301 or call 928-778-6555.

Can I use +P ammunition in my Ruger LCP?
No. The Ruger LCP was not designed for use with +P ammunition. Given the LCP's light weight and compact design, the use of +P ammunition in this particular model may result in damage to the firearm or personal injury.

Does the LCP have a safety?
The design of the Ruger LCP incorporates a variety of safety features. The LCP is a double-action only pistol, which requires a long pull of the trigger to cock the hammer and then release the hammer to fire the pistol. The hammer is inside the slide and protected from a blow. The half cock notch on the internal hammer protects the LCP from jarring off. When the LCP is about to fire, the hammer comes even with the rear end of the slide, signaling the user that slight additional pressure on the trigger will fire the pistol. This pistol also features a manual slide hold open that locks the slide to the rear and allows the user to positively examine the chamber for safety, clearing and cleaning. The loaded chamber indicator view port allows the cartridge in the chamber to be seen when the slide is closed. The magazine itself comes from the factory with a bright orange warning that the pistol is capable of firing with the magazine removed. All Ruger firearms come with external locks, which positively prevent firing when correctly applied and used for safe storage.

Can I dry fire my Mark III pistol?
Yes. The Mark III has a firing pin stop that prevents the firing pin from contacting the rear of the barrel and damaging the edge of the chamber. If you are going to dry fire the pistol extensively, the stop pin and firing pin will eventually wear and contact could occur, and we recommend replacing both the firing pin and the firing pin stop from time to time. You should also monitor the contact of the firing pin with the rear of the barrel.

Why is there a letter stamped on the barrel of my pistol, near the caliber designation?
The stamp on the barrel is a "proof mark" placed on each barrel at the time of manufacture, after the pistol has had a proof round fired through it. This mark serves as additional proof that your Ruger pistol has undergone our normal test firing procedures during manufacture.

What kind of accuracy can I expect from my Ruger autoloading pistol?
The ammunition brand and style used plays an important role in any gun's accuracy and function. We recommend that you determine which type of ammunition is the most accurate in your pistol and stay with that brand while you practice. If you are using unjacketed lead bullets, make sure you clean your barrel, completely removing any lead deposits in the bore. Each pistol has a slightly different point of aim/point of impact relationship.

If you are experiencing an accuracy issue and would like us to target your Ruger firearm, please return it to our Service Department. For the address, click here.

The Ruger P-Series pistols are not produced or marketed as target pistols, but as affordable, reliable service pistols.

What type of ammunition should I use in my Ruger .22 pistol?
The Ruger .22 pistols are chambered only for the .22 caliber Long Rifle cartridge, standard velocity or high-velocity, manufactured to U.S. Industry Standards. Do not attempt to load hyper velocity, .22 Long, .22 Short, or any other type .22 caliber cartridge into the magazine or in the chamber of the pistol. Use of .22 shot shells is not recommended.

What type of ammunition should I use in my Ruger .40 Auto pistol?
The Ruger .40 Auto pistols are chambered for the .40 S&W cartridge and are compatible with all ammunition loaded to U.S. Industry Standards, including high-velocity and hollow-point loads, loaded in brass, aluminum, or steel cartridge cases. .40 S&W ammunition manufactured in accordance with NATO, U.S., SAAMI, or CIP standards is within the design limits and known to function in these pistols.

What type of ammunition should I use in my Ruger .45 Auto pistol?
The Ruger .45 Auto pistols are chambered for the .45 Auto cartridge and are compatible with all factory ammunition loaded to U.S. industry standards, including high-velocity and hollow-point loads, loaded in brass, aluminum or steel cartridge cases, as well as +P ammunition. .45 Auto ammunition manufactured in accordance with NATO, U.S., SAAMI, or CIP standards is within the design limits and known to function in these pistols.

What type of ammunition should I use in my Ruger P94 or P944 pistol?
Both the P94 (9mm) and P944 (.40 Auto) models are roll marked P94 on the slide, and the cartridge for which the pistols are chambered for is clearly marked on the barrel. Only the caliber specified on the barrel should be used in each pistol.

What type of ammunition should I use in my Ruger 9mm pistol?
The Ruger 9mm pistols are chambered for the 9x19mm NATO Parabellum (9mm Luger) cartridge, compatible with the U.S. and foreign military or commercial 9x19mm loads manufactured in accordance with NATO, U.S., SAAMI, or CIP standards, including high-velocity, subsonic, tracer, hollow point, ammunition loaded in aluminum, steel, or brass cartridge cases, +P and +P+ ammunition. Note: The LC9™ is not rated for +P+ ammunition.

Will Ruger replace the barrel on my Ruger P-Series pistol?
Barrels for the Ruger P-Series pistols are factory fitted for correct functioning on an exchange only basis. The complete pistol must be sent to our Prescott Customer Service Department for this service. It is recommended that you contact us prior to sending your pistol to the factory for a barrel replacement at 928-778-6555.

Will Ruger replace the barrel/receiver on my Ruger .22 pistol?
We cannot change the barrel size or type of your Ruger .22 pistol. The barrel/receiver is an integral unit and can only be replaced with one the same size, type and finish as the original. It is serial numbered and is considered to be a 'firearm' by the BATFE. Barrel/receivers are factory fitted on an exchange only basis. The complete pistol must be sent to our Service Department for this service. It is recommended that you contact us prior to sending your pistol to the factory for a barrel/receiver replacement at 928-778-6555.

The Ruger Mark I and Mark II pistols are no longer in production and barrel/receiver replacements for them are not available. The barrel/receiver for the Ruger Mark III pistol is factory-installed and is not sold separately.

How does the bolt stop on my Ruger Mark I pistol operate?
The bolt of the Ruger Mark I pistol does not automatically 'hold open' when the last cartridge from the magazine has been fired and cannot be converted to do so. The user can easily lock the bolt open by pushing upward on the safety while the bolt is held fully to the rear. Please refer to the section regarding 'To Load and Fire' in the instruction manual for more details concerning the bolt operation of this pistol. To download the Ruger Mark I instruction manual, click here.

Will Ruger convert my pistol to another model?
No, the serial number of a firearm, recorded at the time of production, specifies the caliber, finish (blued or stainless) and model description (safety, decocker or double-action). Sturm, Ruger does not offer conversion kits for our pistols and will not change their original, factory specifications.

Does Ruger offer conversion kits for their pistols?
No, Ruger does not offer conversion kits for our pistols.

Will Ruger drill and tap my pistol for a scope base?
Yes. Please contact our Prescott Customer Service Department for price and shipping information.

Can I dry fire my Ruger P-Series and .22 pistols?
Yes. All Ruger pistols can be dry fired without damage, and dry firing can be useful to familiarize the owner with the firearm. However, be sure any firearm is completely unloaded before dry firing!

What should I do if my Ruger .22 pistol or P-Series pistol fails to extract a cartridge?
Carefully follow these steps:


1. Be certain the muzzle is pointed in a safe direction and the safety is 'on'
2. If possible, first remove the magazine. It may be necessary to manually remove a jammed cartridge which has only partially been stripped from the magazine. If so, use extreme care. Lock the bolt open with the bolt stop before attempting to clear the jam. Drawing the bolt fully to the rear may bring the jammed cartridge along. Keep your face away from the ejection port during this operation. When attempting to clear a jam, use only wood 'tools' so that a cartridge will not be ignited if you strike a primer and so that the chamber and magazine will not be damaged. A 3/16" wood dowel rod with a point on one end is useful.
3. Visually check to make sure all cartridges have been removed from the pistol. Safely dispose of any cartridges involved in a malfunction incident. Do not use damaged ammunition in any firearm.

Failure to extract or eject a cartridge clear of the pistol can be the result of the bolt not being pulled rearward vigorously, coupled with an accumulation of bullet lubricant in the chamber. For proper functioning, you should thoroughly clean the chamber and extractor as often as necessary to prevent the accumulation of grease and dirt. For more information on minimizing malfunctions, click here for an instruction manual.

What should I do if my autoloading pistol has feeding issues?
As is the case with any autoloading pistol, you should ensure that the slide rails on the frame and rail grooves in the slide are kept adequately cleaned and lubricated. Check the magazines frequently to be sure the magazine spring firmly returns the magazine follower to the top of the magazine, and that the magazine lips are free of nicks and burrs, and that they are not deformed or cracked. Often, a new magazine will cure any feeding issues. Magazines can be purchased at ShopRuger.com

How do I fieldstrip a Ruger P-Series pistol?
Our instruction manuals contain detailed information regarding the fieldstripping procedures. Further disassembly of the slide or frame components than what is covered in the manuals is not recommended and should only be undertaken by the factory. Click here for an instruction manual.

What is a firing pin block?
The Ruger P-Series decocker model and safety model pistols both have an internal firing pin block, which prevents firing unless the trigger is pulled.

Does Ruger offer a filler screw for the front sight screw hole?
We do not supply filler screws for the front sight hole. The front sight screw hole is tapped to 6-40.

Does Ruger sell grip frames for Ruger P-Series or .22 pistols?
Grip frames are factory installed only, on an exchange only basis. They are not sold as a separate component. Please contact our Prescott Customer Service Department prior to shipping a pistol for a grip frame replacement. For contact information, click here.

How durable are the grip frames on Ruger P-Series pistols?
Our aluminum frames are a hard-coated, aircraft grade aluminum alloy (A356) that has been heat treated to a T61 condition. They are hard-coated for toughness and wear resistance by an anodizing process, similar to that employed in the maintenance of the U.S. M-16 rifle receiver. We also offer pistols with a custom compounded polymer frame with long-strand fiberglass filler. As with any pistol, there is a possibility that the frame can be damaged when dropped.

What type of finish is used on Ruger P-Series grip frames?
The finish on our aluminum frames is a hard-coat anodized finish. This is a very hard and durable coating that actually penetrates the aluminum and builds an outer layer on the frame. Normal handling should not affect this coating; however, surface contact with abrasive objects can cause damage or wear to this finish.

How can I get an instruction manual for my pistol?
Ruger instruction manuals for both currently produced and out-of-production models can be downloaded directly from this website by clicking here. Note that prices listed in manuals are subject to change at any time.

Which magazine should I use in my Ruger Mark I pistol?
The Ruger AMC magazine is no longer produced and has been replaced by the M-9 nine round magazine. This magazine fits the Ruger Standard .22 and Ruger Mark I pistols. The magazine follower button on the M-9 must be moved to the right side of the magazines to fit pre-1971 pistols. Instructions for moving the follower button, if required, are packaged with the magazine. Magazines can be purchased at ShopRuger.com.

Which magazine should I use in my Ruger 9mm pistol?
We produce two different magazines for the Ruger 9mm pistols. The P15 (15 round) and P15/10 (10 round) magazines fit the 9mm pistols with serial numbers below 304-70000 and the P18 (15 round) and P18/10 (10 round) magazines fit pistols with serial numbers above that. They are not interchangeable and will malfunction if used in the wrong pistol. As added information, the Ruger 9MM magazines and the .40 Auto magazines are not interchangeable, even though they appear similar. Magazines can be purchased at ShopRuger.com.

Which magazine should I use in my Ruger .22 pistol?
The magazines for our .22 pistols are not interchangeable. They have physical differences and will not function properly if used in a pistol other than the one for which they were manufactured. They are as follows:

Ruger Firearm Correct Magazine
ModelMagazine
Ruger Standard9 round
Ruger Mark I M-99 round
Ruger Mark II M-1010 round
Ruger Mark II 22/45 AP-1010 round
Ruger Mark III M10MKIII10 round
Ruger Mark III 22/45 AP10MKIII10 round

Magazines can be purchased at ShopRuger.com.

Is the magazine latch on my Ruger .45 Auto pistol ambidextrous?
The magazine latches for the Ruger P90, P97, P345 and SR1911 pistols can only be operated from the left side by pushing inward; they are not ambidextrous. As indicated in the instruction manual's parts listing, there is only a right magazine latch available for these pistols. The magazine release operation of these firearms closely parallels that of the Model 1911 and Ruger 22/45 Rimfire pistols. For an instruction manual, click here.

Does Ruger sell a magazine loader for its .22 pistols?
Yes, Ruger offers a wide variety of Sportswear & Accessories at www.ShopRuger.com.

Does Ruger sell a magazine loader for its P-Series pistols?
Ruger does supply magazine loaders for our P-Series pistols. The PML loader is produced for the 9mm and .40 Auto pistols (Model No.90077), the QML loader for the .45 Auto pistols (Model No. 90087). They are available for purchase at ShopRuger.com. The operation of both loaders is as follows:

a. Insert the first cartridge in the magazine in the normal manner.
b. Place the magazine loader over the top of the magazine with the curved arm at the rear.
c. Place the base of the magazine on a working surface, then apply downward pressure on the magazine loader, far enough to allow you to insert the next cartridge just under the lips of the magazine.
d. Pull the magazine loader up and then push the top cartridge to the rear of the magazine.
e. Repeat c. and d. above until the magazine is fully loaded.

My primers are cratered. What does this mean?
Slight cratering around the firing pin indent on the case primer is normal for our P-Series pistols, caused by the rapid unlocking of the slide. It will not affect the functioning of the firearm.

Will the .22 adjustable rear sight work on all models?
The adjustable rear sight for the .22 LR target models will not work on the .22 LR standard models, and is incorrect for the standard model's front sight.

How do I adjust a Ruger P-Series rear sight?
Adjustment can be made by the use of a 5/64" allen wrench to loosen the lock screw then drifting the sight in the appropriate direction.

Will Ruger reblue or refinish P-Series pistols?
So long as your Ruger P-Series pistol has not been damaged by fire, immersion or corrosion, it can be refinished at our Prescott plant (with the exception of the aluminum frame, which cannot be refinished). The complete pistol must be sent to our Prescott Customer Service Department. Click here for shipping information.

Will Ruger reblue or refinish Ruger .22 pistols?
So long as your Ruger .22LR pistol has not been damaged by fire, immersion or corrosion, it can be refinished at our Prescott plant. The complete pistol must be sent to our Prescott Customer Service Department. Please call for more information at 928-778-6555.

There is rust on my stainless pistol. What should I do?
Firearms made of stainless steel are relatively more resistant to corrosion than blued steel firearms. However, surface discoloration and/or rust can occur as a result of perspiration, contact with some types of holsters and exposure to moisture, humidity, salt air or chemicals. Minor discoloration can usually be removed by rubbing the stained area with an abrasive ink eraser, crocus cloth, or a 'metal polishing' compound. When using any of these abrasives proceed with care and use light pressure to achieve a blending of 'color' with those areas that are not discolored. Exposed surfaces of the firearm should be cleaned and lightly oiled after use or after exposure to adverse conditions.

Does Ruger sell scope mount bases for Ruger .22 pistols?
Ruger produces four scope bases to fit the Ruger Mark I, Mark II, Mark III and .22/45 pistols. The standard Ruger base, part number A07000, is 3.421" long, the distance between the rings is 1.888". The extended base, part number A07001, is 4.125" long, the distance between the rings is 2.625". These bases will only accept Ruger scope rings. We also supply a black 'Weaver-Style' base, part number A07052B, and a gray base, part number A07052G, both will only accept Weaver Rings. Scope bases may be purchased at ShopRuger.com.

These bases require the pistol to be drilled and tapped. However, we do not offer drilling and tapping as a service.

How do I align my P-Series sights?
Both front and rear sights are the white dot type to aid with rapid target acquisition and easy alignment of the sights to obtain a correct sight picture (front sight centered in the rear sight slot). The top of the front sight should be level with the top of the rear sight and the three white dots should appear horizontally aligned.

How should the P-Series slide function?
In order for the slide to function correctly, you must pull the slide fully rearward vigorously then release it quickly, allowing the slide to move forward at its own speed. Do not "ride" the slide forward, as incomplete chambering and a failure to fire may result.

Can I store my Ruger pistol cocked or with rounds in the magazines?
It is seldom advisable to keep a constant load on any compression spring and it is unsafe to store any firearm cocked.

Are the triggers on Standard and Target Model Ruger .22 pistols adjustable?
No, the triggers on both the standard and target model pistols are not adjustable for trigger pull or over-travel.

What is the trigger pull on Ruger .22 pistols when they are manufactured?
Factory specifications are 3 - 5 pounds.

What is the trigger pull on Ruger P-Series pistols when they are manufactured?
Factory specifications are: Single-Action - 4 to 7 pounds, Double-Action - 9 to 15 pounds. A certain amount of 'slack' in the trigger pull is characteristic of these types of Military/Police style pistols.

How do I take advantage of the free safety conversion for Ruger 'old model' single-action revolvers?
Information is available on our website by clicking here.

Please write to us at Sturm, Ruger & Co., Inc. Department KC, Lacey Place, Southport, CT 06890 for full details and a free shipping box.

Will installation of the conversion kit affect the value of my gun?
No. The parts that are removed to install the conversion kit are returned to you in order to preserve the collector's value of your gun, and no permanent alteration is performed to them. We do this because we know these guns are collector's items and we want to encourage 'old model' owners to get this free valuable service from us.

What happens to the parts that you remove when the conversion kit is installed?
The parts are returned to you for collector's purposes.

Can I have my 'old model' single-action revolver serviced or order parts for it without having the conversion kit installed?
No, in order to encourage our customers to take advantage of the free safety update, no service work will be performed on the 'old model' single-action revolvers unless the conversion kit is installed. We also will not sell parts for the revolver unless it has been converted.

Why should I send my 'old model' revolver in for the free safety update?
The patented Ruger Conversion Kit is an entirely new operating system for these revolvers. It can help prevent accidental discharge by a drop or blow to the hammer if the user has failed to take the basic safety precaution of keeping the hammer down on an empty chamber. That's very important!

How can I tell if my single-action revolver is one that is included in the offer for the free safety update?
Three frame screws identify the 'old model' (pre-1973) Single Six, Blackhawk and Super Blackhawk revolvers. Serial numbers below 93-00000 identify old Bearcat and Super Bearcat models. If your revolver has the words 'New Model', 'Bisley', 'Vaquero', or 'Old Army' on the frame, this offer is not applicable.

Will the appearance of my gun be altered by installation of the conversion kit?
No. The frame and other major parts will not be affected by the conversion.

How can I tell if my gun has already had the conversion kit installed?
Be sure to point the gun in a safe direction and ensure that it is unloaded. Then simply pull back the hammer and, if there is a flat bar (transfer bar) between the hammer and frame of the revolver, the gun has been converted.

What will it cost to have the conversion kit installed in my Ruger 'old model' single-action revolver?
Ruger installs the conversion kit free of charge and pays for the shipping charge to return your gun to you. You need only pay to ship the gun to the factory.

I have seen air guns with the Ruger name and logo. Has Ruger begun making air guns?
Ruger has licensed UMAREX USA to manufacture airguns and airsoft guns using the Ruger brand. UMAREX USA is responsible for any production, sale or service of these air guns. If you have questions about these products, please contact UMAREX USA directly using the following contact information:
UMAREX USA
6007 S. 29th St.
Fort Smith, AR 72908
Phone: (479) 646-4210
Website: www.umarexusa.com

I am a resident of California. How do I know which Ruger firearms are available for sale in California?
You can access information on which firearms are available for sale by going to the California Department of Justice link on the Ruger website. Recently introduced models may not appear on the roster because they have not been tested yet, or the testing is completed but they have yet to appear on the roster. Ruger single-action revolvers are exempt from the testing requirements and will not appear on the roster, but are available for sale in California to qualified individuals who meet all federal, state and local requirements.

I am a resident of Massachusetts. The firearm I am interested in purchasing is on the EOPS (Executive Office of Public Safety) list. Does this mean it can legally be sold?
It depends. Some handguns listed on the Approved Firearms Roster might not satisfy certain of the Attorney General's handgun sales regulations. If a handgun does not meet these additional requirements, it cannot be sold. You can obtain more detailed information about those regulations on the Attorney General's website at www.ago.state.ma.us. You can also find information on handguns approved for sale by going to the Massachusetts EOPS link on the Ruger website.

I am a resident of Maryland. How do I know what firearms are available for purchase in my state?
Pistols and revolvers manufactured on or after January 1, 2003 that do not have an 'integrated mechanical safety device' may not legally be sold in Maryland. Conversely, pistols and revolvers manufactured before that date may be sold in Maryland after that date even if they do not have an 'integrated mechanical safety device'. An 'integrated safety device' is a loaded chamber indicator and a magazine disconnect on a pistol, and an integrated locking system in a revolver. You can find information on handguns approved for sale by going to the Maryland Handgun Roster link on the Ruger website.

Is the SR9 available in Maryland?
Any pistol or revolver manufactured after January 1, 2003 that does not have an "integrated mechanical safety device" may not legally be sold in Maryland. As the SR9 does not have such a device when it leaves the factory, it may not legally be sold in Maryland in its as manufactured condition. However, the Maryland Handgun Roster Board does permit the use of certain aftermarket devices to satisfy the integrated mechanical safety device requirement. It also permits retailers and others to independently submit handguns to the Handgun Roster Board for consideration. When we last checked the Maryland Handgun Roster, the SR9 was listed there, which means it was independently submitted and can legally be sold in Maryland provided the "integrated mechanical safety device" requirements are met with an approved aftermarket device and, of course, all other applicable Federal, State and local laws and regulations are satisfied.

Can I place a parts order online?
We currently offer 10/22®, MarkII™ and MarkIII™ spare parts at shopruger.com. For more information
about parts, visit our Parts Ordering Page.

Can I purchase scope rings online?
For additional information about Ruger Scope Rings, click here.

Can I exchange the Ruger scope rings that I received with my new gun for a different sized set?
If the gun was recently purchased and was purchased brand new, we will exchange the new, unused rings that were provided with that firearm with a new set of different model rings more suited to the scope selection. Please note that altered or used scope rings will not be exchanged. Click here for contact information.
Note: Because of the complex US export laws and costs associated with the export of firearm parts, this option is not available to our foreign customers. Please contact the Ruger distributor in your country for information on obtaining scope rings.

I live in New York; what magazines can I purchase from Ruger under the New York Safe Act?
You may purchase any magazine with a maximum capacity of ten (10) rounds. According to the FAQ section found at www.governor.ny.gov/nysafeact/gun-owners, "You may buy, sell, and possess any magazine that can hold up to 10 rounds, regardless of when it was manufactured." Within the state, some municipalities (NYC, Rochester, Buffalo and perhaps others) have additional restrictions. Contact your local authorities to determine if additional restrictions apply.

I live in New York and ordered magazines but have not received them; will I get them?
Yes. New York recently amended the Safe Act to now permit magazines capable of holding up to ten (10) rounds, which had been the law in New York since 1994. Accordingly, all New York orders for legally available magazines will be shipped.

I attempted to place an order for ten-round magazines and was told I could not order them due to the impending change in the law, may I order the magazines now that the law has been amended?
Yes. If you attempted to place an order for magazines capable of holding a maximum of ten (10) rounds and were told your order could not be accepted due to the expected change in the law, please resubmit your order and it will be accepted.

In New York, How many rounds can I load in my magazine?
Beginning April 15, 2013, the New York Safe Act generally prohibits loading more than seven (7) rounds in a magazine. However, according to the to the FAQ section found at www.governor.ny.gov/nysafeact/gun-owners, "While at a recognized range, whether you are there for recreation or for participating in shooting competitions, you may load the full ten rounds into any magazine you have."

I have "grandfathered" magazines that hold more than ten (10) rounds, can I keep them?
According to the to the FAQ section found at www.governor.ny.gov/nysafeact/gun-owners, "If you have a magazine that can contain more than 10 rounds, you have until January 15, 2014 to permanently modify the magazine so that it holds no more than ten rounds, responsibly discard it, or sell it to a dealer or an out of state purchaser." However, magazines manufactured more than 50 years ago are exempt from the prohibition but must be registered pursuant to the New York Safe Act.

I live in New York and I have a modern sporting rifle that has recently been characterized as an "assault weapon" under the New York Safe Act, can I still return my rifle to Ruger for repair?
NO; please do not send these rifles to Ruger for repair because we will not be able to return them to you. There does not appear to be any exemption in the New York Safe Act that allows us to return an "assault weapon" to its owner if it has been sent out of state for repair.

If I send my pistol to Ruger for repair, will my magazines be returned to me?
Magazines capable of holding a maximum of ten (10) or fewer rounds will be returned to you. PLEASE DO NOT SEND MAGAZINES THAT CAN HOLD MORE THAN TEN (10) ROUNDS BECAUSE WE CAN NOT RETURN THEM TO YOU IN NEW YORK.

What firearms does Ruger offer that ship with 10-round (or fewer) capacity magazines?
Ruger has, for many years, offered pistols with magazines that hold ten (or fewer) rounds. Current product offerings include the SR1911, SR45, SR40, SR40c, SR9, SR9c, LC9, LC380, LCP, P95, SR22, Mark III and 22/45. Ruger also offers the 10/22 and Mini-14 autoloading rifles in 10-round (or less) models.

I have not been able to get through to customer service or an operator at ShopRuger.com; what should I do?
Please be patient. We have received an unprecedented volume of calls and are working to increase capacity and improve call center performance.

My order to ShopRuger.com does not appear to be submitted; what should I do?
Please be patient. We have received an unprecedented volume of site traffic and are working to increase capacity and improve performance.

I cannot access ShopRuger.com; what should I do?
Please be patient. We have received an unprecedented volume of site traffic and are working to increase capacity and improve performance.

General FAQs regarding the new Connecticut firearms legislation have been issued by the Connecticut Department of Emergency Services and Public Protection and can be found here: http://www.ct.gov/despp/lib/despp/slfu/faqs_06192013.pdf.

Specific information related to the impact of the new legislation on Ruger products can be found below.

I live in Connecticut; may I purchase magazines from Ruger?
Due to changes in the law that became effective October 1, 2013, Ruger is now required to verify the credentials of Connecticut residents before selling magazines to them. Because our Sportswear and Accessories Department is not staffed or equipped to verify such credentials, we are no longer able to sell magazines to Connecticut residents.

In Connecticut, how many rounds can I load in my magazine?
You may fully load the magazine to capacity at your place of residence, licensed firing range, shooting range or licensed shooting club. Anywhere else, a person may load a maximum of 10 rounds in a magazine, including at your place of business or other property owned by you, while being lawfully transported to a gun dealer or in a pistol with a valid carry permit, providing the magazine does not extend more than one inch beyond the bottom of the pistol grip.

I have magazines with a capacity of more than 10 rounds and I possessed them before April 4, 2013; can I keep them?
Yes, provided you declared the magazines on or before January 1, 2014. If you have additional questions, you should contact the Department of Emergency Services and Public Protection ("DESPP") or your local authorities.

What firearms does Ruger offer that ship with 10-round (or less) magazines?
Ruger has for many years offered pistols with magazines that hold 10 (or less) rounds. Current product offerings include the SR1911, SR45, SR40, SR40c, SR9, SR9c, LC9, LC380, LCP, SR22, Mark III and 22/45 pistols. Ruger also offers the 10/22 and Mini-14 autoloading rifles in 10-round (or less) models. Although the SR-556 is offered in a version with a 10-round magazine, this firearm is not available for sale in Connecticut.

I live in Connecticut and ordered magazines; will I receive them?
Unfortunately, no. Due to changes in the Connecticut law, Ruger is now required to verify the credentials of Connecticut residents before selling magazines. Because our Sportswear and Accessories Department is not staffed or equipped to verify such credentials, we are no longer able to sell magazines to Connecticut residents. All Connecticut magazine orders have been canceled.

I live in Connecticut and I have a modern sporting rifle that is now characterized as an "assault weapon" under the law; can I still return my rifle to Ruger for repair?
Yes, provided you owned the modern sporting rifle before April 4, 2013 and have obtained an "Assault Weapon Certificate." Once you have your "Assault Weapon Certificate," the firearm must then be transferred to a "gun dealer" properly licensed by the State of Connecticut, who may then return the firearm to Ruger for repair. Upon completion of the repair, the firearm will be returned to the gun dealer, to be transferred back to you. Any firearms beyond repair cannot be replaced with another so called "assault weapon." In such circumstances, your firearm will be returned to the gun dealer in as-received condition.

If I send my firearm to Ruger for repair with my high capacity magazines, will my magazines be returned to me?
PLEASE DO NOT SEND MAGAZINES THAT CAN HOLD MORE THAN 10 ROUNDS AS WE MAY NOT BE ABLE TO RETURN THEM TO YOU. Firearms returned to customer service with magazines capable of holding more than 10 rounds will not be returned to Connecticut customers unless the customer can provide a copy of a Certificate of Possession issued by the State of Connecticut in accordance with the law. If you cannot provide a copy of a Certificate of Possession, we are not legally permitted to return the magazines to you.

Are there any firearm parts or accessories I am prohibited from purchasing in Connecticut?
Yes; Connecticut law now defines any part designed or intended to convert a firearm into an "assault weapon" as an "assault weapon." This means that we cannot sell folding or telescoping stocks, pistol grips, thumbhole stocks, forward pistol grips or flash suppressors to Connecticut customers. We are prohibited from selling magazines with a capacity of more than 10 rounds. As noted above, we have ceased the sale of all magazines to Connecticut residents because we are unable to verify credentials required by Connecticut law.

I live in Maryland; what magazines can I purchase from Ruger?
Maryland's new law is effective October 1, 2013. Therefore, as of October 1, 2013, you may only purchase magazines with a maximum capacity of ten (10) rounds.
Check your local magazine capacity laws for any further restrictions.

I have magazines with a capacity of more than ten (10) rounds and I possessed them before October 1, 2013; can I keep them?
If you were a Maryland resident at the time the new law went into effect, then you can keep the magazines. As of October 1, 2013, under Maryland law, "[a] person may not manufacture, sell, offer for sale, purchase, receive, or transfer a detachable magazine that has a capacity of more than 10 rounds of ammunition for a firearm."

What firearms does Ruger offer that ship with 10-round (or less) magazines?
Ruger has, for many years, offered pistols with magazines that hold ten (or fewer) rounds. Current product offerings include the SR1911, SR45, SR40, SR40c, SR9, SR9c, LC9, LC380, LCP, SR22, Mark III and 22/45. Ruger also offers the 10/22 and Mini-14 autoloading rifles in 10-round (or less) models.

I live in Maryland and ordered magazines with a capacity of more than ten (10) rounds; will I receive them?
No, all orders for magazines with a capacity of more than ten (10) rounds for shipment to Maryland were canceled as of October 1, 2013, the date the new law went into effect.

If I send my firearm to Ruger for repair with my high capacity magazines, will my magazines be returned to me?
NO, PLEASE DO NOT SEND MAGAZINES THAT CAN HOLD MORE THAN TEN (10) ROUNDS AS WE WILL NOT BE ABLE TO RETURN THEM TO YOU. Under the new law, it does not appear there is any way for us to legally return the magazines to you.

Where can I find Product Safety Warning and Recall Notice Information?
Product Safety Warning and Recall Notice information can be found in our Safety Announcements sections found here:
Safety Announcements